{"product_id":"victron-smartsolar-mppt-75-15","title":"Victron - SmartSolar MPPT 75\/15 Solar Charge Controller (75V max PV, 15A, Bluetooth) - SCC075015060R","description":"\u003cp\u003e\u003cstrong\u003eThe Victron SmartSolar MPPT 75\/15 is a 15A maximum power point tracking solar charge controller for 12V and 24V systems, with real load terminals built in.\u003c\/strong\u003e It hunts the panel's maximum power point continuously, converts surplus voltage into charge current, and runs a multi-stage adaptive charge algorithm you can override completely if your battery calls for it. Peak efficiency is 98 percent. Bluetooth is built in, so it configures from VictronConnect on your phone with nothing extra to buy.\u003c\/p\u003e\n\n\u003cp\u003eThe 75\/15 is the sweet spot of the small SmartSolar controllers. Same 75V ceiling as the 75\/10, same physical footprint, same load output - but half again the charge current, which lifts the usable array from one panel to a decent pair. It suits caravans, camper trailers, canopy builds, boats and off-grid sheds where the array is modest and the loads are lights, a fridge and phone charging.\u003c\/p\u003e\n\n\u003ch3\u003eHow much solar can you run on a 75\/15?\u003c\/h3\u003e\n\n\u003cp\u003eTwo numbers, and the second one catches people out.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003ePanel wattage:\u003c\/strong\u003e 220W at 12V, or 440W at 24V. That is the nominal PV power the controller converts. Connect more than that and the controller simply limits its output to 15A and clips the rest, which is money spent on panel you never use. Treat 220W at 12V as the working ceiling.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eArray open circuit voltage:\u003c\/strong\u003e this is the harder limit. Maximum PV open circuit voltage is 75V, and maximum PV short circuit current is 15A. Open circuit voltage is not fixed - it climbs as panel temperature drops, so an array that measures comfortably under 75V on a hot day can push higher on a cold morning. Take the Voc figure from your panel label, add cold-weather headroom, and keep the total under 75V. Two 12V-nominal panels in parallel is straightforward. Two in series needs the cold-weather sum done properly before you commit.\u003c\/p\u003e\n\n\u003ch3\u003eIt has a physical load output - and most MPPTs do not\u003c\/h3\u003e\n\n\u003cp\u003eThe larger SmartSolar models do not have one. The 75\/15 does: genuine load terminals rated at 15A continuous. Lights, a small fridge, a USB panel - wire them to the controller and it powers them directly. No relay, no separate module.\u003c\/p\u003e\n\n\u003cp\u003eThe real value is battery protection. The controller drops the load before the battery is flattened. Low voltage load disconnect is selectable at 11.1V or 11.8V, or handed to the BatteryLife algorithm. Reconnect is 13.1V or 14V, or BatteryLife. On lead acid, BatteryLife is the better setting - it moves the disconnect threshold day by day so the bank is not repeatedly parked at a deep state of discharge, which is what shortens their life more than anything else.\u003c\/p\u003e\n\n\u003cp\u003eFor a small build, that is one less box on the wall and one less set of wiring to run.\u003c\/p\u003e\n\n\u003ch3\u003eThe bit no one explains: VE.Smart Networking\u003c\/h3\u003e\n\n\u003cp\u003eA Smart Battery Sense, SmartShunt or BMV-712 reads voltage and temperature at the battery terminals themselves and broadcasts them over Bluetooth. The 75\/15 listens, and sets its charge voltage from that reading rather than from its own terminals.\u003c\/p\u003e\n\n\u003cp\u003eWhy it matters: the controller sits at the far end of a cable. Under charge current that cable drops voltage, so the controller always reads a little higher than the battery really is. It concludes the battery is fuller than it is and tapers early - every cycle, every day. Give it a genuine battery-side reading and the battery actually gets to full.\u003c\/p\u003e\n\n\u003cp\u003eSynchronised charging comes with it. Run more than one SmartSolar MPPT - say a fixed roof array on one and a portable blanket on another - and over the same VE.Smart network they step through bulk, absorption and float together instead of working against each other. A network holds up to 10 devices, but only one sense source is permitted. One sensor feeding many chargers.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUltra fast maximum power point tracking\u003c\/strong\u003e - it earns its keep on cloudy, changeable days\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePeak efficiency of 98 percent\u003c\/strong\u003e - very little lost between panel and battery\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysical load output, 15A continuous\u003c\/strong\u003e - lights or a small fridge run straight off the controller\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBatteryLife load disconnect\u003c\/strong\u003e - adapts the cut-off rather than repeatedly deep-cycling the bank\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAutomatic 12V or 24V battery voltage selection\u003c\/strong\u003e on first power up\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMulti-stage adaptive charge algorithm\u003c\/strong\u003e, or fully user defined for batteries with their own numbers\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEqualisation is disabled by default\u003c\/strong\u003e - available for flooded lead acid, off unless you turn it on\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBluetooth built in\u003c\/strong\u003e - setup, live monitoring and firmware updates from VictronConnect\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVE.Direct port\u003c\/strong\u003e for a wired link to a GX device or a PC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVE.Smart Networking\u003c\/strong\u003e - battery-side voltage and temperature sense, plus synchronised charging with other SmartSolar controllers\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVery low self consumption\u003c\/strong\u003e - 20mA at 12V, 10mA at 24V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtected against PV reverse polarity\u003c\/strong\u003e, output short circuit and over temperature\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eMounting it - read this before you pick a spot\u003c\/h3\u003e\n\n\u003cp\u003e\u003cstrong\u003eThis is an indoor unit.\u003c\/strong\u003e Protection category is IP43 for the electronics and IP22 for the connection area. It is not sealed and it is not waterproof. Do not mount it in an engine bay, under a tray, in a wheel arch, or anywhere it will cop rain, road spray or dust. Inside the canopy, inside the van, in a dry locker or on a shed wall is where it belongs.\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMount it vertically, terminals facing downwards.\u003c\/strong\u003e Not flat on its back, not on its side.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMount it on a non-flammable substrate.\u003c\/strong\u003e The heatsink runs warm under load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLeave clear air above and below\u003c\/strong\u003e so it can convection cool. Boxing it in costs output on hot days.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMount it within 3 metres of the battery, but never directly above it.\u003c\/strong\u003e Close, to limit voltage drop. Not above, because batteries vent.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not mount it in a user-accessible area.\u003c\/strong\u003e The terminals are live.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower terminals accept 6mm2 (AWG10) cable.\u003c\/strong\u003e Size the run for length and current, not just to fill the terminal.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck battery polarity twice.\u003c\/strong\u003e Reverse battery polarity blows an internal fuse that is not practically user-replaceable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe WireBox-S 75-10\/15 terminal cover fits this model\u003c\/strong\u003e if you want the connection area shrouded. Sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eConnect the battery first, then the PV. Disconnect in the reverse order.\u003c\/p\u003e\n\n\u003ch3\u003eFull specifications\u003c\/h3\u003e\n\n\u003cul\u003e\n\u003cli\u003eBattery voltage: \u003cstrong\u003e12V or 24V, automatic selection\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum battery charge current: \u003cstrong\u003e15A\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eNominal PV power at 12V: \u003cstrong\u003e220W\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eNominal PV power at 24V: \u003cstrong\u003e440W\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum PV open circuit voltage: \u003cstrong\u003e75V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum PV short circuit current: \u003cstrong\u003e15A\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003ePeak efficiency: \u003cstrong\u003e98 percent\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eSelf consumption at 12V: \u003cstrong\u003e20mA\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eSelf consumption at 24V: \u003cstrong\u003e10mA\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eLoad output: \u003cstrong\u003eyes, physical, 15A continuous\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eLow voltage load disconnect: \u003cstrong\u003e11.1V, 11.8V or BatteryLife\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eLow voltage load reconnect: \u003cstrong\u003e13.1V, 14V or BatteryLife\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eCharge algorithm: \u003cstrong\u003emulti-stage adaptive, or user defined\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eAbsorption voltage: \u003cstrong\u003e14.4V at 12V, 28.8V at 24V, adjustable\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eFloat voltage: \u003cstrong\u003e13.8V at 12V, 27.6V at 24V, adjustable\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eEqualisation voltage: \u003cstrong\u003e16.2V at 12V, 32.4V at 24V, adjustable, disabled by default\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eTemperature compensation at 12V: \u003cstrong\u003e-16mV\/C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eTemperature compensation at 24V: \u003cstrong\u003e-32mV\/C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eProtection: \u003cstrong\u003ePV reverse polarity, output short circuit, over temperature\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eData communication: \u003cstrong\u003eVE.Direct port and Bluetooth\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eOperating temperature: \u003cstrong\u003e-30C to +60C, full rated output up to 40C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum altitude: \u003cstrong\u003e5000m, full rated output up to 2000m\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eProtection category: \u003cstrong\u003eIP43 electronics, IP22 connection area\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003ePower terminals: \u003cstrong\u003e6mm2 \/ AWG10\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eDimensions: \u003cstrong\u003e100 x 113 x 40 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eWeight: \u003cstrong\u003e0.6 kg\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eColour: \u003cstrong\u003eblue, RAL 5012\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eWarranty: \u003cstrong\u003e5 years\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cdiv itemscope itemtype=\"https:\/\/schema.org\/FAQPage\"\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eHow many watts of solar can I run on a 75\/15?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003e220W at 12V, or 440W at 24V. The second limit is voltage: total array open circuit voltage must stay below 75V, and open circuit voltage rises as the panels get cold. Read the Voc figure off the panel label and allow headroom for a cold morning.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eWhat is the difference between the 75\/10 and the 75\/15?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eCharge current and usable array size. The 75\/10 handles 10A and 145W at 12V. The 75\/15 handles 15A and 220W at 12V. Everything else is the same - same 75V PV ceiling, same physical load output at 15A continuous, same 12V or 24V auto selection, same 100 x 113 x 40 mm case. The 75\/15 is 0.6 kg against 0.5 kg.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eIs it waterproof? Can I mount it in the engine bay?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eNo. Protection category is IP43 for the electronics and IP22 for the connection area, which is an indoor rating. It must not be mounted in an engine bay or anywhere it will see rain, road spray or dust. Pick a dry, ventilated spot inside the vehicle, van or building.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eCan I run lights and a fridge directly from the controller?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eYes. The 75\/15 has a physical load output rated at 15A continuous. It will disconnect the load before the battery is flattened, with a cut-out selectable at 11.1V or 11.8V, or the BatteryLife algorithm which adapts the threshold instead of letting the battery sit deeply discharged.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eWill it charge lithium batteries?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eYes. The charge algorithm is multi-stage adaptive or fully user defined, and the absorption and float voltages are adjustable, so you can dial in whatever your battery manufacturer specifies. Equalisation is disabled by default, which is correct for lithium - leave it off.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eThe sun is up but the controller is showing nothing. Is it broken?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eUsually not. PV voltage must exceed battery voltage plus 5V for the controller to start, and then remain above battery voltage plus 1V to keep running. In weak or early light the panel never reaches that, so the controller stays idle and reports nothing. Normal behaviour, not a fault.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003ch4 itemprop=\"name\"\u003eWhat size cable do the terminals take?\u003c\/h4\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cdiv itemprop=\"text\"\u003e\u003cp\u003eThe power terminals accept 6mm2 (AWG10). Mount the controller within 3 metres of the battery to keep voltage drop in check, but never directly above the battery.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\n\u003ch3\u003eShipping and support\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDispatched from our \u003cstrong\u003eQueensland\u003c\/strong\u003e warehouse, with tracking\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Victron stock\u003c\/strong\u003e, backed by the full \u003cstrong\u003e5 year warranty\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eAustralian owned and operated. Questions before you buy? Call us on \u003cstrong\u003e07 5211 0841\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eSmaller array and a tighter budget? The SmartSolar MPPT 75\/10 is the same unit at 10A. Bigger array or a higher-voltage string and you want the \u003ca href=\"\/products\/victron-smartsolar-mppt-100-15-bluetooth-scc110015060r\"\u003eSmartSolar MPPT 100\/15\u003c\/a\u003e, the \u003ca href=\"\/products\/victron-100-20-mppt-smartsolar\"\u003e100\/20\u003c\/a\u003e, the \u003ca href=\"\/products\/victron-smartsolar-mppt-100-30-solar-charge-controller\"\u003e100\/30\u003c\/a\u003e or the \u003ca href=\"\/products\/victron-smartsolar-mppt-100-50-scc110050210\"\u003e100\/50\u003c\/a\u003e - be aware the 100\/30 and 100\/50 have a virtual load output only, not physical terminals. The rest of the range sits in our \u003ca href=\"\/collections\/victron\"\u003eVictron collection\u003c\/a\u003e.\u003c\/p\u003e\n","brand":"Victron","offers":[{"title":"Default Title","offer_id":46567012696260,"sku":"SCC075015060R","price":86.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2517\/4562\/files\/VictronSmartSolarMPPT75-15-02757.jpg?v=1792107699","url":"https:\/\/www.raingersupplyco.com.au\/products\/victron-smartsolar-mppt-75-15","provider":"Rainger Supply Co","version":"1.0","type":"link"}