Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter
Enerdrive EN1110S 1000W 12V pure sine wave inverter

Enerdrive - 1000W Pure Sine Wave Inverter 12V to 230V - With Remote Switch and 150A Midi Fuse - EN1110S

EN1110S

Regular price $467.00 Sale price
$320.00
Save 31%
/
Tax included. Shipping calculated at checkout.

  • Shipping Available
  • Low stock - order soon
  • Open for backorder - secure yours


Product Description

The Enerdrive EN1110S turns your 12V battery bank into clean 230V AC power. 1000W continuous, true sine wave, one Australian GPO and a 5V USB port, with a remote on/off switch so the inverter can live out of sight in the canopy, cabin or caravan.

True sine wave is the same waveform as household mains. Enerdrive rate it as ideal for motor loads and say it reduces stress on surge protection circuitry, meaning potentially longer equipment life for the appliances you plug in.

You will also need

  • Cable: Enerdrive specify a minimum of 35mm sq cable between the battery and the inverter, with a maximum length of 1.5m. The chassis earth cable must be the same size.
  • Fuse: a DC rated fuse or circuit breaker of at least 150A on the positive line. A 150A midi fuse and holder is included with this listing.
  • Isolator: Enerdrive recommend a DC disconnect switch rated the same as or higher than the fuse, so the inverter can be isolated for service. The inverter's own on/off switch does not disconnect it from the battery.
  • A deep cycle battery bank: Enerdrive highly recommend deep cycle batteries for inverter use, and as much capacity as you can fit. See the run-time table below.

Key features

  • 1000W continuous output, with surge capacity up to 2x rated power for appliances that need more to start
  • True sine wave 230V AC, 50Hz - the Australian mains standard
  • 1 x Australian GPO plus 5V 2.1A USB port
  • USB-only mode - run the USB port with the AC side off to save battery
  • Low no-load draw - under 1.2A
  • Digital display - shows battery voltage, AC output power and error codes, with a green / amber / red status light
  • Audio alarm with warning codes, so you are alerted before the unit shuts down
  • Automatic shutdown for overload, over temperature and low or high battery voltage
  • 6m remote on/off switch included
  • Mounting brackets and heavy duty DC stud connectors for permanent installation
  • RCM marked, meets all required Australian Standards
  • 5 year Enerdrive warranty

Installation - straight from the Enerdrive manual

  • Enerdrive recommend all wiring is done by a certified technician or electrician.
  • Mounting: any orientation except with the DC input panel facing down. In an RV it must be mounted horizontally.
  • Clearance: allow at least 75mm around the unit. Never cover the cooling fins or fit it in a zero-clearance compartment.
  • Location: indoors, away from direct sunlight, heat, moisture and corrosive environments. Not near flammable fumes or gases, such as gas bottles or large engines.
  • Earth: the chassis must be earthed through the ground stud. Never run the inverter without it.
  • Polarity: reversing the DC input damages the unit beyond repair and is not covered by warranty.
  • After off-road use: Enerdrive advise checking the IEC plugs are fully inserted, and again every 6 months.

Full specifications

  • Model: EN1110S
  • AC output power: 1000W
  • AC output current: 4.3A
  • AC output voltage: 230V AC / 50Hz
  • AC output waveform: true sine wave
  • AC outlets: 1
  • USB output: 5V, 2.1A
  • Nominal DC input voltage: 12.5V DC
  • DC input operating range: 10.5 - 15.5V DC
  • No-load battery draw: under 1.2A DC
  • Under-voltage alarm: 11.2V DC
  • Under-voltage shutdown: 10.5V DC
  • Under-voltage recovery: 11.8V DC
  • Over-voltage shutdown: 15.5V DC
  • Compliance: RCM, all required Australian Standards
  • Operating temperature: 0C to 40C
  • Storage temperature: -20C to 60C
  • Relative humidity: 5 - 90% non-condensing
  • Operating altitude: up to 3000m
  • Dimensions (W x L x H): 177 x 325 x 90mm
  • Weight: 2.9kg
  • Warranty: 5 years

Estimated run times

Enerdrive's figures, based on a 12V 240Ah battery bank discharged to 50%. Actual run time will vary with your batteries and their condition.

  • Cordless phone (5W): 80 hrs
  • Clock / radio (8W): 65 hrs
  • Table lamp (40W / 60W): 22 hrs / 15 hrs
  • Freezer, 8.8 cu ft (80W): 12 hrs
  • 20 inch LCD TV (100W): 10.5 hrs
  • Refrigerator, 18 cu ft (120W): 8.3 hrs
  • Mid-size microwave (1000W): 44 min

What's in the box

  • Enerdrive ePOWER 1000W inverter (EN1110S)
  • Remote cable and momentary on/off switch with facia
  • 150A midi fuse and holder
  • User manual

Frequently Asked Questions

What cable and fuse does the EN1110S need?

Enerdrive specify a minimum of 35mm sq cable with a maximum run of 1.5m between the battery and the inverter, and a DC rated fuse or circuit breaker of at least 150A on the positive line. A 150A midi fuse and holder is included with this listing.

Is it 230V or 240V?

The output is 230V AC at 50Hz, which is the Australian mains standard, through a standard Australian GPO. Treat the outlet the same as a wall socket at home.

Will it run a microwave?

Enerdrive's own run-time table lists a 1000W mid-size microwave at about 44 minutes on a 240Ah bank. Check the rated input power on your microwave's label. If it is over 1000W, step up to the Enerdrive 2000W EN1120S-X.

How much power does it use when nothing is plugged in?

Under 1.2A with the inverter on. If you only need to charge phones, USB-only mode runs the 5V USB port with the AC side switched off to save battery.

Where can I mount it?

Indoors - inside the canopy, cabin or caravan - away from direct sunlight, heat and moisture, with at least 75mm of clearance around it. Enerdrive say not to use it near flammable fumes or gases such as gas bottles or large engines. Any orientation is fine except with the DC input panel facing down, and in an RV it must be mounted horizontally.

Does the on/off switch isolate the battery?

No. The on/off switch and the remote switch do not disconnect DC power. Enerdrive recommend a DC disconnect switch, rated at or above your fuse, so the inverter can be isolated before any work is done on it.

What warranty does it have?

5 years from Enerdrive. Damage caused by connecting the DC input in reverse polarity is not covered.

Need more power? See the 2000W EN1120S-X or the 2600W EN1226S-X. Browse the full Enerdrive 12V range.

Enerdrive EN1110S 1000W 12V pure sine wave inverter

Built By Adventurers

We've always believed in leaving no stone left unturned, Our products are no different


Recently viewed